This Quick Start section assumes that you have MATCHED your in-game settings in the GAMEPACK Config, but have yet to otherwise change any GAMEPACK settings.
In its default configuration, this GAMEPACK contains four loadouts, each able to contain their own Primary and Secondary Optimized Weapon and optional Anti-Recoil adjustment settings.
This GAMEPACK uses bright and dim LEDs to display information.  Details on this will be covered in each section.  You can also view our video tutorials below:
With an Xbox® STRIKEPACK™, your LED colours will look like this when they are lit up...
...but for the sake of this manual, we will just focus on whether they are bright, dim, or off.

After selecting this GAMEPACK, you will be greeted with LEDs displaying your Active Loadout along with Weapon Swap's current position.
Loadout Selector and Weapon Swap will be explained in their own sections but for now this is how your LEDs could be arranged:
While HOLDING , or the ACTIVATOR PADDLE BUTTON: TAP to change your Active Loadout.
Active Loadout 1:
Active Loadout 2:
Active Loadout 3:
Active Loadout 4:

On its default Automatic setting, Weapon Swap will keep track of your SWITCH WEAPON button presses...
...automatically swapping between the Primary and Secondary Weapon settings.
You will also have manual control over this as Weapon Swap Auto will lose sync with the game at times, such as upon respawning.
TAP to swap to your Primary Weapon Settings.
TAP to swap to your Secondary Weapon Settings.
TAP to swap to the Regular Weapon position.
TAP to swap to the MODs Disabled position.
The STRIKEPACK™ LEDs will assist you in keeping track of Weapon Swap's current position:
Primary Weapon:
One Heavy Rumble.
Secondary Weapon:
Two Heavy Rumbles.
Regular Weapon:
Three Heavy Rumbles.
MODs Disabled:
One Light Rumble.
Correct (Weapon Swap Synced):
Using Primary Weapon & Synced :)
Using Secondary Weapon & Synced :)
Incorrect (Weapon Swap Lost Sync):
Using Primary Weapon & Lost Sync :(
Using Secondary Weapon & Lost Sync :(

When using the Weapon Selector, explained in its own section...
...the STRIKEPACK™ will display flashing LEDs.  The bank of four LEDs can change sides; this is to help with the counting of flashes that you will be doing shortly.
Pay attention to the single LED on its own; this is the Weapon Category LED.
Important: Before using the Weapon Selector, ensure that Weapon Swap is synced up to your current weapon.
Navigate to the Weapon Category that your weapon belongs to:  TAP to navigate left; TAP to navigate right.
TAP to cycle through the available weapons within the selected Weapon Category.  Each time you feel a rumble, the flashing count restarts.  Count the number of flashes from the moment that you feel the rumble to determine which weapon you are selected on and when you are on the correct weapon, RELEASE , or the ACTIVATOR PADDLE BUTTON to confirm your selection.
Weapon Category
Weapon Category LED
Weapons Within Category (Count Flashes)
1: Regular Fire, 2: Rapid Fire, 3: Tap Quickscope, 4: Release Quickscope
1: BR75 Battle Rifle, 2: CQS48 Bulldog, 3: Hydra, 4: MA40 Assault Rifle, 5: Mangler, 6: MK50 Sidekick, 7: VK78 Commando
1: Needler, 2: Plasma Pistol, 3: Pulse Carbine, 4: Ravager, 5: Stalker Rifle
Hard Light:
1: Heatwave, 2: Sentinel Beam
1: Disruptor, 2: Shock Rifle
1: Cindershot, 2: Energy Sword, 3: Gravity Hammer, 4: M41 SPNKR, 5: S7 Sniper Rifle, 6: Skewer

Quick Edit Anti-Recoil, explained in its own section...
...is an optional setting that provides you with the means to fine tune the Optimized Anti-Recoil for your current weapon which you may need to do if you are using weapon attachments or deviating from the recommended in-game settings in some way.  You also can use Quick Edit to manually set Anti-Recoil for any of the "Generic" fire options.
Ideally, you should have either selected the weapon beforehand with the Weapon Selector, or assigned the weapon to the weapon slot beforehand in the GAMEPACK Config.
How you adjust Quick Edit will vary based on the Anti-Recoil Mode that you have selected:
  • Using the default Off-Enemy setting, you should be adjusting by pointing at the general environment such as walls or non-enemy targets where you will see the pattern of bullet holes.
  • Using the optional On-Enemy or Dynamic settings, you should be adjusting with a friend on the opposite team for the best result; otherwise just use a wall.  Just remember that you have to FULLY HOLD your FIRE TRIGGER all the way down when testing Dynamic on an enemy.
    Before entering Quick Edit Mode, ensure that you are synced up to your current weapon so that the correct Optimized Anti-Recoil is being applied.
     Enter Quick Edit Mode to adjust and test the Anti-Recoil for your current weapon.
    While HOLDING , or the ACTIVATOR PADDLE BUTTON, HOLD until you feel a pulsing rumble.
    At this point, some of your controls will be restricted, but you will still be able to test your current weapon.  Anti-Recoil in this GAMEPACK is AIM DOWN SIGHTS ONLY so remember to do so while testing.
You will be HOLDING or TAPPING the D-PAD to adjust Anti-Recoil.  You will feel heavy rumbles as you adjust until you otherwise reach the adjustment ceiling or floor.  For the Vertical Anti-Recoil, DOWNWARDS pulls down, and UPWARDS pulls up.  For the Horizontal Anti-Recoil, RIGHTWARDS pulls right, and LEFTWARDS pulls left.
Warning: It may be impossible to achieve perceptively perfect results, especially if the weapon has randomized recoil or if the weapon attachment drastically alters the recoil pattern, so please manage your expectations.
If you mess things up, reset Anti-Recoil to default by HOLDING until you feel two heavy rumbles.
To save and exit Quick Edit Mode, PRESS .